How to Get Old Tint Off Car Windows

Download Article

Download Article

If your window tint is too dark or is scratched, discolored, or bubbly, you can easily remove it without spending a lot of money, whether you're working with vehicle or home windows. You don't even need to spend hours scraping away the tint with a razor and scrubbing off the adhesive! Using a steamer is the easiest and least damaging method, so that's your best option. Alternatively, you can spray the windows with ammonia, cover them with garbage bags, and let the combination of sun and ammonia dissolve the adhesive before peeling the tint away.

1. 1

   Roll your vehicle window down ¹⁄₄ inch (0.64 cm). Open your vehicle door so you can access the inside of the tinted window. Crack your window just a little so that you are able to reach the very top and see the edge of the tint.^[1]

   • Do the windows in the doors first and save the rear window for last, especially if it has defrost capabilities. This will give you a chance to practice your technique so you can remove the tint more easily while making sure not to mess up the defrost lines.
   • If you're doing windows in your home, you can skip this step.

2. 2

   Steam both the outside and the inside of the windows. Any handheld clothing or upholstery steamer will work for this project. Hold the steamer 1–2 inches (2.5–5.1 cm) away from the window and steam the entire outside of the window first. Then, apply steam to the inside of the window. Work in long, sweeping motions from the top to the bottom and try to heat the pane of glass evenly.^[2]

   • Steaming the outside helps heat up the window enough for the adhesive to dissolve. You don't need to do this for the rear window of your vehicle or if the windows in your home are on the second level and you can't access them easily, though.

   Variation: If you don't have a steamer, you can use a hairdryer or heat gun to loosen the adhesive instead. However, this takes longer, isn't as effective, and will probably leave behind a lot of glue that you'll need to clean off. Just be sure not to heat the glass so much that it breaks!

   Advertisement

3. 3

   Use a straight razor to lift up the edge of the tint. Carefully place a straight razor underneath the tint at one corner of the inside of the top of the window. Using a razor to loosen the edge of the tint will make it easier to peel off.^[3]

   • If you can't get the corner of the tint to come up, apply more steam and try again.

   EXPERT TIP

   Chad Zani is the Director of Franchising at Detail Garage, an automotive detailing company with locations around the U.S. and Sweden. Chad is based in the Los Angeles, California area and uses his passion for auto detailing to teach others how to do so as he grows his company nationwide.

   

   Chad Zani
   Auto Detailing Expert

   Our Expert Agrees: Glass is difficult to scratch, so you can run a razor blade across the glass with a lubricant to remove the tint. You can also use a razor blade to remove the sticky residue that is left behind after the tint is gone. Another option to remove the sticky residue is using a citrus-based cleaner.

4. 4

   Peel the tint off slowly while continuing to apply steam. Work slowly and pull the tint down from the top of the window toward the bottom of the window. Keep applying steam, paying special attention to any particularly stubborn spots.^[4]

   • If you try to pull the tint too quickly, it will tear and make the job that much harder. If that happens, use the razor to lift the edge of the tint again and continue peeling it off.

   Warning: The steam is incredibly hot so be very careful not to burn yourself as you remove the tint!

5. 5

   Remove any remaining adhesive with a commercial cleaner. Mix 1 part commercial cleaner, like 409, and 1 part water in a spray bottle so you can easily apply it to the window.^[5] Spray it on and scrub the glue spots with a non-scratch pad, then dry the glass with a paper towel.

   • Wipe the door panels or window frame with a clean microfiber cloth to remove any water from the steaming process.^[6]

6. 6

   Repeat the process on each tinted window. You can use the same technique to remove the tint from each of the windows in your vehicle or home. Go slow and take your time so that you can remove all of the tint from each window in a single piece.

7. 7

   Steam the back window of your vehicle for 7 minutes before peeling the tint away. If you're working on a vehicle, position the steamer right up against the interior glass of the back window. Tie something around the trigger to keep it going and prop up the steamer so it stays in place. Close the doors to your vehicle and let the steamer run for 7 or more minutes.^[7]

   • Then, loosen the edge of one of the top corners and slowly peel the tint away from the glass. Be super careful not to damage the defrost lines.^[8]
   • Lower or remove the rear seats, or at least the headrests, if possible, to give yourself better access to the rear window.^[9]

   Advertisement

1. 1

   Mask the door panels of your vehicle or the window frame in your home. To protect them from the ammonia, cover the interior door panels or window frame with tarps or plastic sheeting and tape it in place. Don't use newspaper or another absorbent material as the ammonia will soak through it.^[10]

   • Be sure to cover all of the electrical components in your vehicle well, such as switches and speakers.

   Tip: This method works best on hot, sunny days as the heat from the sun helps the ammonia break down the adhesive holding the tint to the glass.

2. 2

   Cut black garbage bags to the size of your windows. Place a black garbage bag over one of the windows and use a metallic marker to trace the outline. Cut it out and separate the bag so you have 2 pieces: 1 for the inside of the window and 1 for the outside. Repeat for each window.^[11]

   • You only need to cover the inside of the windows with garbage bags if you're working on windows in your home and can't easily reach the exterior.

3. 3

   Apply soapy water to the outside of the windows and put the garbage bags on top. Fill a spray bottle three-quarters full of water and add a squirt of dish soap. Shake up the bottle and spray the outside of each window. Then, place a garbage bag to the glass so it covers it completely.^[12]

   • The soapy water helps the garbage bag stick to the window.
   • Skip this step if you can't access the outside of the windows in your home.

4. 4

   Spray ammonia on the inside of the windows and cover them with the garbage bags. Fill another spray bottle with ammonia. Spritz the inside of a window so it's fully saturated then press the garbage bag into place so it covers the glass. The liquid should hold the plastic in place all on its own, but you could use masking tape to secure the bags if necessary. Repeat for each window.^[13]

   • If you don't want to use ammonia or don't have any on hand, you can use a mixture of water and soap or baby shampoo on the inside of the windows, instead.^[14]

   Warning: Wear gloves and a mask or respirator when working with ammonia to protect your skin and lungs.

5. 5

   Let the ammonia soak in for 1-2 hours. Give the sun time to heat up the glass, which will help the ammonia dissolve the adhesive holding the tint to the windows. This is best to do in the middle of summer on a really hot, sunny day.^[15]

6. 6

   Remove the bags and peel the tint away. Take off the garbage bags, then use a razor to peel 1 corner of the tint away from the window so you can grip it. Slowly and carefully pull the tint away from the glass from one edge of the window to the other.^[16]

   • Work slowly so the tint doesn't rip! If it does, slide the razor underneath the edge of the tint so you can lift it up and continue removing it.

7. 7

   Use ammonia and steel wool to remove any glue stuck to the windows. Once you've gotten all of the tint off, spray the window with ammonia again. Scrub any stuck-on adhesive with fine steel wool. Then, wipe away the debris and liquid with newspaper.^[17]

   • If the adhesive doesn't come off easily, use a razor to scrape it away, being careful not to damage the window.^[18]
   • A large razor scraper will make the process easier, especially if you're working on windows in your home.^[19]

   Advertisement

Add New Question

• Question

  How can I remove window tint on the inside of a car?

  

  The steamer option seems most promising if it will keep the adhesive with the tint film. Alternatively, you can rip the film off in seconds, leaving the adhesive behind. As an R&D engineer, I experimented with a variety of solvents from weak isopropyl alcohol to powerful acetone. The adhesive was most soluble in 91% isopropyl alcohol (70% rubbing alcohol might work well also). A spray bottle with the alcohol in one hand and a narrow plastic paint scraper in the other removes the adhesive quickly while the adhesive flecks dry rapidly and land on the floor. Avoid breathing vapors. Small areas or residues are easily scrubbed off with the alcohol on a rag followed by streak free window cleaner.

• Question

  Is the tint on the inside or outside of the front windows?

  

  The tint is virtually always on the inside for protection from the elements. If it's on the outside, it's probably because whoever installed it did not read the instructions before installation.

• Question

  If I peeled off the cooling film without heating or applying any liquid, but the glue residue remains, how do I remove it?

  

  Use wet soapy water with a razor blade and clean the entire window. Afterwards, use automotive glass cleaner to give it the final clean.

• Question

  Will the razor scratch the window?

  

  Yes, if you press directly into the glass. You should always keep the razor blade at an angle from the glass, and don't press too hard.

• Question

  Can I use a white garbage bag?

  

  You can, but it will take longer because black retains heat while white reflects it. Adjust your times accordingly.

• Question

  Most trucks have plastic sliding back windows. I have one, so any type of razor is out. What can I do?

  

  A non-metallic scraper should do the trick. You can pick one up at any hardware store for about 5 bucks.

• Question

  Can "goo gone" remove window tint?

  

  Goo Gone can't remove the tint itself, but it can remove the adhesive that keeps the film attached to the glass.

• Question

  Will the sun work if it is cold outside?

  

  No, it will take a forever. Your best bet is to get a heat gun and it will melt it right off.

• Question

  How long do I leave the garbage bags on the car?

  

  In the sun (heat) about 20+ minutes, then start peeling and spraying as needed to keep it wet.

• Question

  Can I use a blow dryer for the heat?

  

  Yes, best to use one of the older-style types.

Show more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Video

• Never scrape across defroster lines with a razor blade as this can damage them.

• Be careful not to burn yourself when working with a steamer or heat gun.

Advertisement

Things You'll Need

• Steamer
• Straight razor
• Commercial cleaner
• Non-scratch pad
• Paper towels
• Microfiber cloth

• Tarp or plastic sheets
• Masking tape
• Black trash bags
• Scissors
• Soapy water
• Ammonia
• Spray bottles
• Razor blade
• Very fine steel wool
• Newspaper

About This Article

Article SummaryX

To remove window tint, try using a razor blade and soapy water. First, use the razor blade to make a cut in the corner of the window tint so you can peel up the film. Then, grasp the cut corner and peel the film off of your window. If it doesn't come off in one piece, repeat the process with the rest of the film until it's all off. Fill a spray bottle with water and dish soap, and spray the soapy water onto your window. Carefully scrape off the adhesive left from the window tint with the razor blade, applying more soapy water as you go. Finally, clean your window with a glass cleaner and paper towels once you've removed all of the adhesive. You can also remove window tint using a hairdryer. First, turn the hairdryer on high and hold it 2 inches (5 cm) away from one of the corners on the window tint for 30 seconds. Then, use your fingernail or a razor blade to peel up the corner of the film. Continue to heat sections of the film for 30 seconds at a time, slowly peeling it up as you go. Once the film is all off, rub off any remaining adhesive with a towel. For tips on removing any leftover tint adhesive from the glass, read on!

Did this summary help you?

Thanks to all authors for creating a page that has been read 2,444,115 times.

Did this article help you?

How to Get Old Tint Off Car Windows

Source: https://www.wikihow.com/Remove-Window-Tint

Share this post